How it works
A staff bead with the seal built in
This is a retrofit product. Swap your old staff bead for this one and you can draught proof your existing sash window, without replacing the window. The staff bead (also called a stop bead) runs around the inside of the window frame and holds the bottom sash in place. Ours is solid pine with no finger joints, and comes with the brush seal included free and already installed. It closes the gap where draughts and rattles get in, and it's ready to fit on site.
Becomes part of the window
The brush sits in a slot cut into the timber and faces away from the room, into the window. Once installed you can't see it, so you'd never really know the bead had been swapped.
See it on a real window: can you spot the draught proofing? →
The fin does the sealing
A fin runs through the middle of the brush. Fit the bead so it touches the sash and it forms the seal, with an extra barrier to noise.
Smoother to operate
The sash runs against the brushes, so it slides up and down more smoothly. Compression seals aren't suited to sliding windows.
Which width?
Match the width of your old bead
Both widths are 18mm deep, with the same brush seal and timber.
Suits staff beads around 22mm wide.
Suits wider staff beads, around 30mm.
View the 30mm bead →How to check: measure across the face of the bead that holds your bottom sash in place. Not sure? Send us a photo or call 02 7228 0625 and we'll help.
How much do I need?
Measure each side and the top
Choose your lengths
A double hung window usually needs a staff bead down each side and one across the top. Measure each run and pick lengths that cover it in one piece, then cut to fit.
As a guide, our draught seal kit includes two 2m and two 1m staff beads for a window up to 2m high and 1m wide.
DIY Draught Seal Kit
Staff beads and parting beads with the brush pre-fitted, a meeting rail draught stopper and sash cord. Everything to seal one double hung window.
Installation
Fit it yourself
Watch the video below, and call us if you get stuck. We're happy to help.
Remove the old bead
Cut through the paint line with a sharp knife, then gently lever the old staff bead off.
Measure and cut
Measure each side and the top, and cut the new bead to length.
Position it
Push the bead up to the sash so the fin touches it, but the window still slides freely.
Fix and paint
Pre-drill and nail it in place, then give the timber its final coats. Keep paint off the brush.
Watch the installation video
Tools you'll need
A sharp utility knife, a flat pry bar or chisel, a tape measure and pencil, a fine-tooth saw, a drill for pre-drilling, a hammer and 40mm nails.
Tips for a good seal
Have everything on site before you start, as courier delays do happen.
Fit the bottom sash first, then set the staff bead against it. Too tight and the sash will drag. Too loose and the fin won't seal.
Check your beads now and then, and replace any damaged sections.
Specifications
Product details
Made from solid pine. As a natural material, it may have knots, grain variation and minor marks. These don't affect how the bead performs.
Ideal for
- Retrofitting draught proofing to existing sash windows
- Double hung sash windows
- Replacing worn or damaged staff beads
- Cutting draughts, rattles and dust
- Keeping a traditional look on period homes
From our blog
Read more about our beading
Questions
Good to know
What's the difference between a staff bead and a parting bead?
The staff bead sits on the inside and holds the bottom sash in. The parting bead sits in the middle of the frame and separates the two sashes. For a full seal, you'll usually replace both. See our draught seal parting bead.
Which brush colour should I choose?
It's your choice. Pick the colour you'd rather see against your paintwork. If a colour shows as sold out, call us and we'll let you know when it's back.
Does it need painting?
Yes. The bead comes pre-primed, ready for your final coats once it's installed. Keep paint off the brush so it stays soft and seals well.
How does delivery work?
We deliver Australia-wide, and shipping is calculated at checkout. Orders are usually picked and packed within 2 business days. Delivery times are estimates, so allow extra time around public holidays.
Can I pick up in Sydney?
Yes, pick-up is free from our warehouse in Warriewood, just off Mona Vale Road. Choose Pick up at checkout and we'll message you the address when your order is ready.
I need a lot of beading, or I'm a tradie
Call us on 02 7228 0625 for bigger orders and trade pricing.
Not sure what your window needs?
Send us a photo or give us a call. We're happy to help before you buy, or while you're fitting it.


